Multifactor Non-linear Modeling for Accelerated Stability Analysis and Prediction - Pharmaceutical Technology

Latest Issue
PharmTech

Latest Issue
PharmTech Europe

 Pharmaceutical Technology All results
Multifactor Non-linear Modeling for Accelerated Stability Analysis and Prediction
The right approach can provide a clear, statistically defendable method for determining dissolution and accelerated stability.
 Jul 2, 2014 Pharmaceutical Technology Volume 38, Issue 7, pp. 46-49

Accelerated stability analysis is a strategy used to quickly evaluate alternative formulations, packaging, and processes. Accelerated linear studies are commonly performed and modeled; however, accelerated multiple-factor non-linear modeling has been a gap, and statistical software tools such as SAS/JMP do not directly have any provision to model multiple factor nonlinear responses. This paper outlines an approach to model and predict non-linear multiple factor stability/tablet dissolution data under accelerated and nominal storage conditions.

 RELATED CONTENT Data Integrity in the Analytical Laboratory More Rapid Extractable & Leachable Analyses with Advanced Mass Spectrometers More Analytics

There are many non-linear stability cases such as dissolution, leachables, and moisture. Being able to model these non-linear processes is crucial to proper drug development.  In addition to general non-linear modeling, there are multiple factors that may influence the non-linear curve. The following is a list of factors that may impact the asymptotes, growth rate, and inflection point of a curve:

• Stability storage temperature and humidity
• Particle size
• pH
• Amount of an excipient
• Processing conditions and/or set points
• Packaging materials/method

Study design
Proper design of experiments for data collection and curve isolation is crucial for building non-linear models. Figure 1 illustrates the factors that should all be square relative to all other factors and have zero correlation relative to each other. For this tablet dissolution example, multiple time points (minutes), multiple storage conditions (temperature), multiple drug substance particle sizes, and multiple weeks were measured. Percent dissolution was the response of interest.

Analysis method
The following is a step-by-step procedure for non-linear stability modeling and expiry determination.

Step one. Measure the data at multiple time periods, using multiple particle sizes and at multiple temperatures. Generate a plot of the data to visualize the relationship of the curves over time  (25-10-0: 25=Temperature, 10=Particle Size, and 0 = days) (see
Figure 2).

Step two. Fit each curve individually. In this example, each dissolution curve was fit using a four-parameter logistics (4PL) curve. The four parameters are: upper asymptote, lower asymptote, inflection point, and slope of the dissolution curve.  R-Square should be high (typically above 0.95) and RMSE error should be low for each curve.  Outliers should be checked using the residuals.  Save the parameters of the curve.  In this example, there are four parameters, upper asymptote, lower asymptote, growth rate (slope), and inflection point (see Figure 3).

Step three. Save the parameters from the curve and the factors that influence them into a table. For this example, the growth rate and inflection point are the coefficients that may change the most based on the factors under consideration. The upper and lower asymptotes are not of concern for this problem as all of the curves have similar lower asymptotes and similar upper asymptotes, but upper and lower asymptotes could be important for other problems, so generally it is best to model all of the curve parameters (see Figure 4).

Step four. Fit the curve parameters with a least-squares multivariate regression. Growth rate, the slope of the 4PL fit, and inflection point are the most important as the dissolution starting point and the upper asymptote are essentially the same for all curves. Main effects and interaction models generally work best and p-values and F tests can be used to evaluate each model term (see Figure 5).

Step five. Save the equation from the multivariate parameter model.  An example of the inflection point model is in Equation 1.
[Eq. 1]

Step six. Substitute the growth rate (slope) and inflection point coefficients from the multivariate model into the nonlinear prediction.  The red box in Figure 6 shows the substitution for the inflection point.

Step seven. Check the model to make sure it matches the actual data. Correct any modeling errors by adding or modifying a multivariate model term. A simple YX regression plot of the model versus the measurement will indicate model quality and any systematic errors (see Figure 7).

Step eight. Create a profiler from the equation to predict future dissolution rates.  This can be done using a modern statistical package such as SAS/JMP (see Figure 8).

Step nine. Predict dissolution at any time, temperature, or particle size combination using the profiler.  For this example, particle size was set to 5 μm, temp to 25 and time in weeks to zero.  The dissolution time was fixed at 100 min with a specification of not less than 90% (see Figure 9).

Step ten. From the profiler at each time point (weeks), make sure the time (min) and particle size (5 um) are fixed, determine dissolution at the nominal temperature (non-accelerated condition).  Fit the rate of degradation using either a linear or nonlinear model from the profiler predicted data.  In this case, the rate of dissolution is not linear so a non-linear curve is fit to the data and the expiry is determined based on the extrapolated curve (see Figure 10).
The same method is used for predicting both the nominal expiry and the 95% CI expiry.

Step eleven. Finally, long-term stability evaluation at nominal storage conditions will be used to confirm the early model prediction and will provide an independent secondary determination of stability and changes in dissolution.  Understanding rates of change should factor into shelf life and release specification limits (1).

Summary
Non-linear multiple factor analysis has long been a problem in a variety of process and product modeling and prediction. The novel procedure discussed in this paper for the characterization of multiple factor non-linear product performance provides a clear, statistically defendable method for determining dissolution and accelerated stability. Long-term verification of accelerated conditions should always follow early determinations of expiry, acceleration rates, and rates of degradation.

Reference
1. ICH, Q6A Specifications: Test Procedures and Acceptance Criteria for New Drug Substances and New Drug Products: Chemical Substances (Oct. 6, 1999).

Mark Alasandro, PhD, is director, Allergan Irvine. Thomas A. Little PhD, is president, Thomas A. Little Consulting, drlittle@dr-tom.com.

| Weekly
| Monthly
|Monthly
| Weekly
 Survey
FDASIA was signed into law two years ago. Where has the most progress been made in implementation?
Reducing drug shortages
Breakthrough designations
Protecting the supply chain
Expedited reviews of drug submissions
More stakeholder involvement
Reducing drug shortages 70%
Breakthrough designations 4%
Protecting the supply chain 17%
Expedited reviews of drug submissions 2%
More stakeholder involvement 7%
Most Viewed Articles
 Columnists Outsourcing Outlook Eric LangerTargeting Different Off-Shore Destinations sponsored by Ingredients Insider Cynthia ChallenerAsymmetric Synthesis Continues to Advance Regulatory Watch Jill Wechsler Data Integrity Key to GMP Compliance European Regulatory WatchSean MilmoExtending the Scope of Pharmacovigilance Comes at a Price