Strategic Approaches to Process Optimization and Scale-up - Pharmaceutical Technology

Latest Issue
PharmTech

Latest Issue
PharmTech Europe

Strategic Approaches to Process Optimization and Scale-up
The authors present three approaches that a contract development and manufacturing organization can consider when designing development and process-optimization studies that will provide useful data for scaling up a project.


Pharmaceutical Technology
Volume 34, Issue 9

As the development of a new drug product progresses, the batch sizes manufactured generally increase. The early First Time in Man (FTIM) clinical trials commonly involve dosing to a small number of subjects, with the majority of the manufactured product often being required for stability studies and analytical testing. As one proceeds from formulation design to Phase I clinical trials and subsequently through to Phase II & III, batch sizes generally increase. Following a successful clinical trial outcome, resulting in the granting of a marketing authorization, the batch sizes manufactured may be further increased to cover the market demands.

Current International Conference on Harmonization (ICH) guidelines state that data from stability studies should be provided on at least three primary batches of the drug product (1). The primary batches should be of the same formulation and packaged in the same container-closure system as proposed for the marketed formulation. The manufacturing process used for these primary batches should simulate that to be applied to production batches and should provide product of the same quality and meeting the same specification as that intended for marketing. Two of the three batches should be at least pilot-scale batches and the third one can be smaller, if justified. Where possible, batches of the drug product should be manufactured by using different batches of the drug substance. Typical batch sizes used throughout development as defined in the European Medicines Agency's (EMA) guidance for Process Validation are laboratory-scale, pilot, and production-scale batches (2).

Laboratory-scale batches. These are produced at the research and early development laboratory stage. They may be of very small size (e.g., 100–1000 times less than production scale). Laboratory-scale batches may be used to support formulation and packaging development, early clinical and/or preclinical stages. Laboratory-scale batches can also be analyzed to assist in the evaluation and definition of critical quality attributes (CQAs). A CQA is a physical, chemical, biological, or microbiological property or characteristic that should be within an appropriate limit, range, or distribution to ensure the desired product quality. CQAs are generally associated with the drug substance, excipients, intermediates, and drug product.

Pilot-scale batches. These may be used in the process-development or optimization stage. They may be used to support preclinical and mid- to later-stage clinical evaluation and also to support formal stability studies. If supporting formal registration, a pilot-batch size should correspond to at least 10% of the production-scale batch. For oral solid-dosage forms, this size should generally be 10% of production scale or 100,000 units, whichever is greater. The choice of pilot scale is often difficult for the project team as members must balance parameters such as anticipated product volumes, anticipated site of production, equipment constraints at that site, and regulatory expectations. With the increasing trend toward developing orphan drugs, the authors believe that the regulatory expectation of pilot-scale batches of 100,000 units is not always valid and should be discussed with the relevant regulatory authority.

Production-scale batches. These batches are of the size that will be produced during the routine manufacturing and marketing of the product. Data on production-scale batches may not always be available prior to granting marketing authorization.

Approaches to process optimization and scale-up

Pharmaceutical development activities around the scaling-up and optimizing for pilot- or commercial-scale manufacture should include, at a minimum, the following elements (3):

  • Defining the target product profile as it relates to quality, safety and efficacy, considering, for example, the route of administration, dosage form, bioavailability, dosage, and stability
  • Identifying CQAs of the drug product, so that those product characteristics having an impact on product quality can be studied and controlled
  • Determining the quality attributes of the drug substance and excipients, and selecting the type and amount of excipients to deliver drug product of the desired quality and efficacy
  • Selecting an appropriate manufacturing process
  • Where possible, identifying a control strategy.

The basis of quality-by-design (QbD) follows that well-designed experiments, carefully planned and thought out from the outset of formulation development, can produce quality data from an early stage, which can minimize lengthy and costly repetition of manufacturing and subsequent studies and analysis. Nevertheless, before manufacturing registration batches, it is usual to invest additional time and effort in challenging, and, where necessary, optimizing the existing manufacturing process. This is achieved by making additional development batches at laboratory-scale, pilot scale, and possibly even at production scale. The output from the above development efforts provides the basis for justification that scale up can be achieved without a consequent loss in quality and/or efficacy and provides the link between formulation and process development, pilot-scale manufacture, and eventual commercial production.

Analysis of the data assists in determining the parameters that have a known effect upon a CQA of the drug product. These parameters are referred to as being critical process parameters (CPPs). Furthermore, data obtained creates a picture of the product and process, how its design has evolved, what is critical and must be controlled, and proven acceptable ranges (PARs) around specific process parameters.

This article presents three approaches that a CDMO can consider in designing development and process optimization studies that will provide useful data on scaling up a product.

Approach 1: Quality ensured by end-product testing

This method of manufacturing is a minimal approach to the mechanistic understanding of a process. The development is mainly empirical with research often conducted one factor at a time (OFAT). Following manufacture, there would be little or no 'design space' defined, resulting in a strict manufacturing process that should be adhered to in order to minimize any variability in product characteristics and thus the CQA profile. Validation will primarily be based on initial full-scale batches. CPPs are determined using only prior knowledge. Proven acceptable ranges for CPPs are not fully determined. A minimal knowledge of PARs is determined. The following is an example of how this approach is used in developing a film-coated tablet.

Example 1: Blend, direct compression, and coating scale-up operation. A blending operation at a specified scale is performed using a standard tumble blender. The drive unit is set to a fixed speed. The excipients are added to the blending shell and tumbling is initiated. The blend is mixed for a set period of time. Following this mixing time, the blend is sampled to determine blend uniformity and bulk assay values. If the blend is determined to be uniform, the time and speed used is recorded and would be used for future batches. If the blend is found to be nonuniform at this stage, an additional mixing period is used, followed by further sampling for uniformity and bulk assay. This procedure is repeated until uniformity is achieved with the mixing time and speed recorded for future batches.

The uniform blend is compressed using a suitable tablet press for the batch size in question. The compression parameters are adjusted in order to obtain the desired product characteristics such as tablet weight, hardness, thickness, disintegration time, and dissolution time. Compression force and compression speed would be adjusted during set-ups and continually assessed with appropriate adjustments made. Intensive in process checks continuously monitor product quality characteristics in order to maintain an acceptable product.

The tablet cores are progressed for coating using a batch coating process. The coating parameters are initially set using prior knowledge of the equipment being used and coating at a particular batch size. Intensive in-process checks, in addition to close visual observations by trained operators, allow adjustments to be made throughout the coating process. The final parameters would be recorded and used for future coating operations at this scale.

With the advent of the guideline ICH Q8 Pharmaceutical Development, this historical approach is falling out of favor, and would likely invite greater scrutiny from regulatory authorities following submission (3).

Approach 2: Full design of experiments

An enhanced QbD approach to product development would additionally include a systematic evaluation, understanding, and refining of the formulation and manufacturing process, including (3):

  • Identifying–using prior knowledge, experimentation, and risk assessment–the material attributes and process parameters that can have an effect on product CQAs
  • Determining the functional relationships that link material attributes and process parameters to product CQAs
  • Using the enhanced process understanding in combination with quality risk management to establish an appropriate control strategy that can, for example, include a proposal for design space(s) and/or real-time release.


Figure 1: An Ishikawa (fishbone) diagram that identifies all potential parameters that can have an impact on the desired quality attribute. (ALL FIGURES COURTESY OF THE AUTHORS)
Risk-assessment tools can be used to identify and rank potential parameters deemed to have an impact on product quality based on prior knowledge and initial experimental data. The initial list of all possible parameters can be quite extensive, but is likely to be narrowed, as process understanding is increased, to a smaller list of potential parameters. Narrowing the list has the advantage of reducing the number of experiments necessary in the modeling of a design space. The list can be refined further through screening experimentation to determine the significance of individual parameters and potential interactions. Once the significant parameters are identified, they can be further studied (e.g., through a combination of design of experiments, mathematical models, or studies that lead to mechanistic understanding) to achieve a higher level of process understanding.


Table I: The potential parameters in an example analysis.
Example 2: Full design of experiments. Using prior scientific knowledge, the project team experts will use the target product profile to establish CQAs, and, in turn, CPPs. An approach could follow the five steps listed below.


Figure 2: Example C&E diagram detailing dry-mixing and granulation parameters.
Step 1: Cause and effect analysis (Ishikawa diagram). The expert team compiles a cause and effect (C&E) diagram, also known as an Ishikawa diagram, that maps out all potential parameters in a manufacturing process. The number of parameters can be very extensive. An example analysis performed for a recent project at Almac resulted in 79 parameters, possibly influencing the final tablet quality (see Figure 1). The parameters determined are shown in Table I. Figure 2 shows the potential CPPs making up the dry granulation step of the manufacturing process.


Figure 3: Example parameter rating form.
Step 2: Ranking of process parameters in order of importance. The list was analyzed using a risk-assessment approach to prioritize the parameters. Parameters graded as high risk were progressed for investigation. An example parameter rating form is presented in Figure 3. The example shows a parameter rating form focusing on the nine parameters from the dry-granulation stage that may have an effect on the CQAs. A separate rating form would be completed for each stage of the manufacturing process. A scoring system, ranging from 1 being minimal effect, 3 being moderate, and 9 having a major effect on product attributes, was used. This scoring approach applies a much greater weighting to parameters deemed to impact a product's attributes significantly, thus increasing the necessity to further study the effect of the particular variable.


Figure 4: Example results parameter rating form.
Figure 4 shows an example of results following the compilation of the scoring process. The example illustrated focuses on a single product attribute (tablet hardness) and a single processing step (dry granulation). The full exercise produces individual tables compiling project team views regarding each processing parameter in relation to each CQA.


Figure 5: Parameter evalution to determine which parameters should be investigated.
Figure 5 shows how decisions can be made on which parameters may be investigated at the next stage. The total score is the sum of the scores obtained for process parameters across all the CQAs. This will provide a rank order of parameters that may have an effect on CQAs. Using prior experience coupled with knowledge of the intended process, the number of parameters can be minimized. The number of parameters investigated using experimental design will significantly increase the number of batches required.


Figure 6: Detail of parameter risk assessment.
Step 3: Assessing the impact of parameters on the product. The parameters were further screened by considering the higher ranked parameters in each processing step as having a high influence on each CQA. Also, every parameter having a score of 40 or more was classified as having a high influence on CQAs. An example matrix showing the impact assessment for the dry granulation step is presented in Figure 6.


Table II: Parameters to be investigated in example analysis.
Step 4: Determine the parameters to be investigated experimentally. Following a full analysis using prior knowledge and experience of the formulation and the manufacturing techniques, conclusions will be drawn from the risk-based classification process to list the parameters to be investigated using a first-screening experimental design (see Table II).

The parameters were investigated using a 2-level screening design of experiments. In this example, 10 parameters were chosen to be screened.


Figure 7: The relationship between the number of parameters and resolution of design to the number of experiments required.
The number of parameters, in addition to the desired resolution of the design, impacts on the number of experiments required in determining the critical parameters. Figure 7 shows the relationship between number of parameters and resolution with number of experiments required. Additional considerations such as time and active pharmaceutical ingredient constraints may also influence the number of experiments that are possible at this stage.


Figure 8: Standard experimental design notation.
The standard experimental design notation is presented in Figure 8, where X is the number of levels being investigated. A level is a particular parameter value. In the case of compression speed, the two levels could be the maximum and minimum turret speed that would potentially be used in an operation. K is the number of parameters being investigated. P is the degree of fractioning that is being performed in order to reduce the number of experiments. A full factorial design would not have a value for p displayed.

For example, 25 would be a two-level design covering 5 parameters. This would require 32 experiments to investigate the parameter effects. 25-1 is a fractional design of this example where the number of experiments required is halved to 16. As the degree of fractioning increases the quality of information obtained from the design decreases. A typical approach would be to use a high-quality (high resolution) design for optimization and in-depth study of a process and use a low-resolution design for initial screening in order to determine critical parameters. The design would then generate a number of experiments that detail the exact parameters to set for a manufacturing operation. Each experiment would be completed and the subsequent product attributes would be determined. Statistical software is used to analyze the effect of the process parameters on the product attributes and determine how critical each parameter is.


Figure 9: The influence of granulator final screen size and roller pressure on tablet hardness.
In the described example, the results of the experimental design allowed the number of potential critical parameters for the initial screening to be reduced to eight. These eight parameters were then investigated using a more comprehensive 3-level design. This type of design, also referred to as a response surface method (RSM), will require more experiments. The previous 2-level screening design is used to minimize the number of parameters investigated so as to minimize the number of experiments at the 3-level design stage. In this example, the results of the 3-level design enabled statistically significant models to be calculated showing the effects of the critical parameters on a number of product attributes. A graphical example of a model displaying the influence of granulator final screen size and roller pressure on tablet hardness is shown in Figure 9. As can be seen, as the roller pressure and granulating screen size decreases, the tablet hardness increases.

Step 5: Design space. The linkage between the process inputs (input parameters and process parameters) and the CQAs can be described in the design space. The risk-assessment and process-development experiments described can not only lead to an understanding of the linkage and effect of process inputs on product CQAs, but also help identify the parameters and their ranges within which consistent quality product can be achieved.

Approach 3: Hybrid method combining elements of approaches 1 and 2.

The use of a full design of experiments approach can result in a significant amount of batches being manufactured to cover the design space. As the number of batches required to describe the design space increases, the development time and cost increases. A third method combining elements from approaches 1 and 2 optimizes the balance between development time and cost and maintains a good understanding of the manufacturing process. This hybrid approach can be achieved by breaking the manufacturing process into defined sections. The initial blending step can be performed using Approach 1. The blend could be manufactured to specification, and end-product testing will show the quality (e.g. blend uniformity/assay). Parameters such as blending time and blending speed can be determined by intensive blend uniformity and bulk-assay analysis allowing blending windows to be established. A second confirmatory batch could be manufactured using the parameters obtained from the initial batch that could provide additional confidence in the manufacturing process.

The blend will have been shown to meet specification and can then be progressed to the next processing steps. An experimental design approach can then be performed. For example, the next steps could involve dry granulation followed by compression into tablets. As described in approach 2, following completion of a full risk assessment and subsequent cause and effect diagram detailing the potential process parameters, a structured design of experiments plan can be devised. Rather than completing each experiment at the full scale, the experiment can be performed using a suitably sized aliquot of the blend manufactured already. As both dry granulation and compression are a continuous throughput process, the parameters investigated are mainly independent of batch size used. Using this approach, a 60-kg blend could be divided into 3-kg sublots, allowing up to 20 experiments to be run.

Following completion of the experiments and analysis of the data, a confirmatory batch could be manufactured using the optimized parameters determined from statistical analysis and preparation of a design space. The resulting batch or tablet cores could be progressed to coating if required. Again, the coating process can be investigated using method 1 or 2.

Conclusion

Strategies for product development can vary from company to company and from product to product, and as such, a contract development and manufacturing organization (CDMO) must be able to provide a service that can suit the requirements of any customer. For a variety of reasons, a company might choose either an empirical approach or a more systematic approach to product development. The approaches described can aid in the provision of a high-quality development offering from the outset while striving to control timelines and costs, which are commonly seen as opposing forces in the pharmaceutical industry.

Conor P. Long* is a senior formulation development scientist and John Mc Quaid is a technical development manager, both at Almac Pharma Services, 22 Seagoe Industrial Estate, Craigavon, BT63 5QD, UK, tel: +44 (0) 2838 363363, fax +44 (0) 2838 363300,
.

*To whom all correspondence should be addressed.

References

1. ICH, Q1A (R2) Stability Testing of New Drug Substances and Products, (ICH, Geneva, Feb. 2003).

2. EMA, Note for guidance, Process Validation, CPMP/QWP/848/96, (EMA, London, Sept. 2001).

3. ICH, Q8 (R2) Pharmaceutical Development, (ICH, Geneva, Aug, 2009).

ADVERTISEMENT

blog comments powered by Disqus
LCGC E-mail Newsletters

Subscribe: Click to learn more about the newsletter
| Weekly
| Monthly
|Monthly
| Weekly

Survey
What role should the US government play in the current Ebola outbreak?
Finance development of drugs to treat/prevent disease.
Oversee medical treatment of patients in the US.
Provide treatment for patients globally.
All of the above.
No government involvement in patient treatment or drug development.
Finance development of drugs to treat/prevent disease.
23%
Oversee medical treatment of patients in the US.
14%
Provide treatment for patients globally.
7%
All of the above.
47%
No government involvement in patient treatment or drug development.
9%
Jim Miller Outsourcing Outlook Jim MillerOutside Looking In
Cynthia Challener, PhD Ingredients Insider Cynthia ChallenerAdvances in Large-Scale Heterocyclic Synthesis
Jill Wechsler Regulatory Watch Jill Wechsler New Era for Generic Drugs
Sean Milmo European Regulatory WatchSean MilmoTackling Drug Shortages
New Congress to Tackle Health Reform, Biomedical Innovation, Tax Policy
Combination Products Challenge Biopharma Manufacturers
Seven Steps to Solving Tabletting and Tooling ProblemsStep 1: Clean
Legislators Urge Added Incentives for Ebola Drug Development
FDA Reorganization to Promote Drug Quality
Source: Pharmaceutical Technology,
Click here