Applying Dry Powder Coatings - Pharmaceutical Technology

Latest Issue
PharmTech

Latest Issue
PharmTech Europe

Applying Dry Powder Coatings
The authors experiment with a resonant acoustic mixer as a method for dry powder coating.


Pharmaceutical Technology
Volume 35, Issue 10, pp. 94-102

Efficient handling and transport of fine-particle powders can be difficult because of the highly cohesive nature of the bulk powder mass. It is well reported in the literature that the application of nanosized guest dry powder coatings, such as silicon dioxide, onto the surfaces of these cohesive host particles can effectively reduce the attractive forces between them (1–5). The fine nanoparticles increase the spacing between the host particles and increase the apparent surface roughness, which decreases the host particle cohesive van der Waals attractions (5, 6). After dry powder coating, the bulk powder exhibits increased bulk density, improved powder flow performance, and easy fluidization behavior, all of which can significantly improve manufacturing performance (1–5). This result is of significant benefit to pharmaceutical powder processing because the easy transport of large bulk quantities of powder through unit operations is necessary to manufacture solid dosage forms such as capsules and tablets.

It was recently demonstrated that conventional pharmaceutical processing equipment, namely a comil, can effectively apply dry powder coatings of silicon dioxide onto active pharmaceutical ingredients (APIs) and excipients without causing attrition of the host's primary particles (1). This discovery is important because comils can be operated in a continuous manufacturing process and are commonly available at pharmaceutical product manufacturing sites. Although the comil is a simple, effective, and scalable unit operation for applying dry powder coatings, the systematic study of the process operational design space, such as screen size and impeller speed, may be required to optimize the coating performance. This iterative method may not be possible in early drug product development because of the limited available quantities of API (often less than 50 g) and the potential for improved performance after dry powder coating may be overlooked, especially as API synthesis, isolation, and sizing processes change often. Therefore, alternative (or complementary) methods for applying dry powder coatings would be desirable during early product development.


Figure 1: Laboratory-scale resonant acoustic mixer (LabRAM), including the vacuum–deaeration unit (left), mixing unit (center), and control unit (right). (FIGURE 1 IS COURTESY OF RESODYN CORPORATION)
A laboratory scale resonant acoustic mixer (LabRAM) similar to the one shown in Figure 1 was evaluated as a potential tool for dry powder coating (7, 8). The LabRAM is a sophisticated bench-top mixer that exploits low frequency, high intensity, acoustic energy to rapidly fluidize and disperse as much as 500 g of a variety of materials. The RAM uses acoustic energy to mix the desired media through an oscillating mechanical driver that accelerates the mixing vessel by as much as 100 times the acceleration of gravity. The propagation of mechanical energy through a system of plates, weights, and springs creates an acoustic pressure wave in the mixing vessel. The frequency of the driver is optimized by the control system so that the system operates at resonance. By operating at resonance, the acoustic energy is absorbed by the media. The efficient mixing is accomplished by creating a homogenous shear zone throughout the mixing vessel without imparting excess energy and without the aid of mixing media or impellers. This approach seems promising because the RAM can mix at high acceleration and amplitude and therefore induce significant shear strain within the bulk powder in a short time. Related work by Davé and coworkers has demonstrated that when high degrees of shear are induced (e.g., by impact coaters) to disperse fine particles, the particles preferentially adhere to the surface of larger host particles after processing (2, 3, 5).

In this study, the RAM was evaluated as a tool for applying various dry powder coatings, such as silicon dioxide, to pharmaceutical excipients and APIs. The effect of these coatings on powder bulk density, particle size, and shear cell flow performance were used as indicators of performance enhancement, and the results were compared to those of dry powder coating using a comil.


ADVERTISEMENT

blog comments powered by Disqus
LCGC E-mail Newsletters

Subscribe: Click to learn more about the newsletter
| Weekly
| Monthly
|Monthly
| Weekly

Survey
What role should the US government play in the current Ebola outbreak?
Finance development of drugs to treat/prevent disease.
Oversee medical treatment of patients in the US.
Provide treatment for patients globally.
All of the above.
No government involvement in patient treatment or drug development.
Finance development of drugs to treat/prevent disease.
23%
Oversee medical treatment of patients in the US.
14%
Provide treatment for patients globally.
7%
All of the above.
47%
No government involvement in patient treatment or drug development.
9%
Jim Miller Outsourcing Outlook Jim MillerOutside Looking In
Cynthia Challener, PhD Ingredients Insider Cynthia ChallenerAdvances in Large-Scale Heterocyclic Synthesis
Jill Wechsler Regulatory Watch Jill Wechsler New Era for Generic Drugs
Sean Milmo European Regulatory WatchSean MilmoTackling Drug Shortages
New Congress to Tackle Health Reform, Biomedical Innovation, Tax Policy
Combination Products Challenge Biopharma Manufacturers
Seven Steps to Solving Tabletting and Tooling ProblemsStep 1: Clean
Legislators Urge Added Incentives for Ebola Drug Development
FDA Reorganization to Promote Drug Quality
Source: Pharmaceutical Technology,
Click here