Assessment of Large-Sample Unit-Dose Uniformity Tests - Pharmaceutical Technology

Latest Issue

Latest Issue
PharmTech Europe

Assessment of Large-Sample Unit-Dose Uniformity Tests
The authors describe the concept of the limiting discriminatory threshold (LDT) as an objective means of evaluating the inherent quality requirement of a large-sample content-uniformity test.

Pharmaceutical Technology
Volume 35, Issue 10, pp. 82-92

Large sample size UDU test proposals

The hUSP test is designed to accommodate a small sample size (i.e., as many as 30 units), but PAT-associated on-line methods permit a much larger sample size from each commercial batch. An alternative "large n" UDU test is thus needed. Several proposals have appeared in recent years, and a brief review is provided below.

Sandell proposal. Sandell et al. proposed a nonparametric counting test for sample sizes between 100 and 10,000 units (2). The maximum number of defect units, whose content exceeds the range of 85–115% LC, is equal to the median of the binomial distribution defined by a sample size (n), and a defect probability of 1 – 0.952 = 0.048. The authors demonstrated that the test has lower acceptance probability than that of the hUSP test as long as the probability is at or below 50%. However, the choice of the binomial median and defect probability of 0.048 is somewhat arbitrary and remains a point of controversy.

Bergum and Vukovinsky proposal. Bergum and Vukovinsky suggested a nonparametric test with a defect-count limit equal to the largest integer less than or equal to 3% of total sample size (3). OC curves are used to make various comparisons with the Sandell and hUSP tests. However, as with Sandell's proposal, the choice of 3% seems somewhat arbitrary.

Diener proposals. Diener et al. proposed several parametric alternatives for sample sizes in the range of 31 to 99 (4). As they did with Sandell's approach, the authors demonstrated with OC curves that their tests were more stringent for batches with at most 95.2% coverage. But, again, it is not clear that the inherent quality levels that the tests represent are widely accepted.

The key to any large sample UDU test is to define the underlying quality threshold that distinguishes an acceptable batch. Each of the above proposals makes assumptions about the acceptable coverage or defect rate. For example, both Sandell's and Diener's approaches chose 95.2% coverage as the quality requirement, while the Bergum and Vukovinsky proposal led (in the large sample limit) to a coverage of 97% as the quality requirement. The quality requirement of a large-sample UDU test should ensure good product quality and should be at least as stringent as the quality requirement of the hUSP test. OC curves are often used to evaluate large-sample UDU tests, but they depend on test characteristics (e.g., sample size) and parameters of the population distribution, thus requiring the generation and unwieldy comparison of a large number of OC curves. It would seem desirable to summarize the performance of any proposed large-sample UDU test using a single quality criterion.

Limiting discriminatory threshold

Formally, a limiting discriminatory threshold (LDT) is defined as the large sample limit of the inverse of the probability of acceptance function in Eq. 1. The concept of LDT for a large-sample UDU test is motivated by the following ideas and assumptions:

1. The key critical quality parameter of content uniformity is coverage.

2. A coverage threshold of less than 100% that unambiguously distinguishes between acceptable and unacceptable batches should be agreed upon.

3. UDU tests exhibit both Type I (i.e., rejection of acceptable batches) and Type II (i.e., acceptance of unacceptable batches) errors. As sample sizes increase, the test becomes more discriminatory. In the ideal limit of infinite sample size (i.e., the true coverage of each lot is known with absolute certainty), the error probabilities are zero, and the OC curve is a step function. In this article, the coverage at which this transition occurs is called the LDT, defined in the following equation as the converging limit with increasing sample size:

4. The LDT of a given UDU test represents its inherent quality-discriminating threshold in the ideal limit of complete knowledge (i.e., infinite sample size) and can be determined algebraically or by computer simulation.

5. To be considered equally stringent, UDU tests, at a minimum, should have the same LDT. Tests with the same LDT may approach the LDT at different rates as sample size increases. When comparing two large-sample UDU tests that have the same LDT, the test that approaches the LDT more rapidly can be considered more efficient.

An LDT of 100%, while certainly desirable, is not realistic because of inherent analytical uncertainty. The LDT and the rate of approach to the LDT will depend not only on the test itself, but, in some cases (e.g., parametric tests), also on the distribution of the population from which samples are drawn.

The LDT concept may not be limited to single coverage, but is applied to the 85–115% LC coverage here for illustration. In principle, the concept could be extended to multivariate quality metrics (e.g., joint coverage of 75–125% and 85–115% LC ranges), although that approach is not considered here.

It is legitimate and useful to determine the LDT for compendial tests (e.g., hUSP test) that employ fixed sample sizes. Such tests rarely define a quality requirement (i.e., the required coverage to pass the test) explicitly. When a definitive quality metric, such as coverage, can be identified, LDT provides a reasonable way to reverse engineer the intended standard of quality. Multistage tests are often designed such that the acceptability range is widened as the fixed sample size (i.e., stage) increases because the estimation of the population information has improved. This design reduces the risk of the Type I error and maintains a nominal Type II error rate. Ultimately, the criteria applied at the final stage set the standard for expected quality and decision error rates. Consequently, when evaluating the LDT of fixed-sample-size tests, the acceptance criteria of the final stage should be kept constant with changing sample size. If the content of all individual units were known, the coverage would be known exactly and could be compared with the LDT that is inherent to the final stage of the test. This procedure effectively assumes that batch acceptance would be based on the perfect knowledge of the batch uniformity, had it been available.


blog comments powered by Disqus
LCGC E-mail Newsletters

Subscribe: Click to learn more about the newsletter
| Weekly
| Monthly
| Weekly

What role should the US government play in the current Ebola outbreak?
Finance development of drugs to treat/prevent disease.
Oversee medical treatment of patients in the US.
Provide treatment for patients globally.
All of the above.
No government involvement in patient treatment or drug development.
Finance development of drugs to treat/prevent disease.
Oversee medical treatment of patients in the US.
Provide treatment for patients globally.
All of the above.
No government involvement in patient treatment or drug development.
Jim Miller Outsourcing Outlook Jim MillerOutside Looking In
Cynthia Challener, PhD Ingredients Insider Cynthia ChallenerAdvances in Large-Scale Heterocyclic Synthesis
Jill Wechsler Regulatory Watch Jill Wechsler New Era for Generic Drugs
Sean Milmo European Regulatory WatchSean MilmoTackling Drug Shortages
New Congress to Tackle Health Reform, Biomedical Innovation, Tax Policy
Combination Products Challenge Biopharma Manufacturers
Seven Steps to Solving Tabletting and Tooling ProblemsStep 1: Clean
Legislators Urge Added Incentives for Ebola Drug Development
FDA Reorganization to Promote Drug Quality
Source: Pharmaceutical Technology,
Click here